Ap.Setup | Ap Extender Login | 192.168.10.1

WAVLINKlogo
CONNECTING YOUR WiFi RANGE EXTENDER
ERROR INSTALLING WIFI RANGE EXTENDER............. 94%
wavlink setup

Your Device Is Not Connected To Wifi Network ! Click New Extender Setup For Quick Installation Or Follow The Steps Given Below.

Note: These Instructions apply only to following extenders.

  • AC1200 mesh extender
  • outdoor wifi range extender
  • Wing 12m Range Extender
  • AC1200 Aerial hd2 Extender
  • AC600 Wifi Extender
  • Quantum d4g extender

Don’t Let WiFi Troubles Slow You Down. Chat With Our Live Agents For Quick Help.

Ap.Setup | Ap Extender setup | 192.168.10.1

The Ap.setup is open from any device with a web browser, such as Google Chrome, Edge, or Firefox.You must ensure that your device is connected to a repeater in order to successfully connect to ap extender login.

Wavlink Aerial AC1200 Extender setup

Ap Extender login | Ap.setup

An Access Point (AP) is a networking device that allows wireless devices to connect to a wired network. In the context of a WiFi extender, the AP setup mode refers to where the WiFi extender is configured to act as an access point instead of a repeater.

  • Connect the Extender to the plug.
  • Use your web browser for access to Ap.setup right away.
  • To access the Ap Setup page, enter your username and password.
  • You may configure and manage your Wavlink extender once you’ve logged in.
  • If ap.setup isn’t functioning, contact our help.
  • During initial Ap.setup, make sure your extender is close to the router.
ap extender setup

Wavlink extender setup via ap.setup

wavlink AC1200 setup

To log in to your Wavlink wifi extender setup, follow these steps:

  • Make sure that your extender is powered on and connected to your computer or mobile device.
  • Open a web browser and enter ap.setup or 192.168.10.1 in the address bar. This will take you to the Wavlink extender login page.
  • Enter the username and password for the extender. If you haven’t changed the default login credentials, the default username is “admin” and the default password is “admin”.
  • Once you’re logged in, you should be able to access the extender’s web interface and configure its settings as needed.

Receive professional setup assistance for your wavlink devices, exclusively provided by ap-setup.online.

Quantum D4G Extender Setup

Wavlink Quantum D4G setup

The Wavlink Quantum D4G Extender is a device that can extend the range of your Wi-Fi network. Here are the general steps to set up the Quantum D4G Extender:

  • Plug in the Quantum D4G Extender into a power outlet near your Wi-Fi router.
  • Press the WPS button on the Quantum D4G Extender and then on your Wi-Fi router within 2 minutes. This will establish a secure connection between the devices.
  • Wait for the connection to be established. The Power LED and the Signal LED should turn solid green.
  • Move the Quantum D4G Extender to the location where you want to extend your Wi-Fi signal. Make sure it’s within range of your router’s Wi-Fi signal
  • Connect your device (such as a laptop or phone) to the Wi-Fi network of the Quantum D4G Extender. The Wi-Fi network name (SSID) and password are located on the label on the device.
  • Once connected, you should be able to access the internet.

How to wavlink Ac1200 extender setup via wps?

Wavlink AC1200 Wps Setup

Wavlink Extender can also be set up via the WPS. Your router must support the WPS capabilities in order for this method to function. Here is a guide on how to set up Wavlink Extender in WPS mode.

  • Place the router and extender in the same area.
  • You may observe the light blinking via finding the WPS button on the Wavlink Range Extender and pressing and holding it for 2–3 seconds.
  • Push your router’s WPS button at this point.
  • A connection is being created when the WPS lights on the extender and router both blink for 10 to 15 seconds.
  • The WPS light on the router will stop blinking once the connection between the two devices has been set up, while the WPS light on the repeater will stabilise.
wavlink extender wps setup

wavlink wing 12m setup

wavlink wing 12m setup​

The Wing AC1200 12m Range Extender user manual:

  • Connect the Wing Extender to the wireless devices.
  • Enter ap.setup or the IP address 192.168.10.1 to open the browser.
  • Log in using the default username and password to reach the setup page.
  • The repeater scans the area for any warnings.
  • To choose your home’s WiFi network, click it.
  • Click Next after entering the WiFi setup. Wait 30 seconds before connecting your amplifier to your home network.
  • Now that the Wing 12m Extender units have been installed.
    Place the extender next to the area without internet to boost connectivity.

Note: If You Need Any Assistance Regarding You Wavlink Extender So Get In Touch With Our Technician Via Live Chat.

Wavlink Aerial AC1200 Extender Setup

Wavlink Aerial AC1200 Extender setup
  1. Connect the extender to the power outlet.
  2. When any smart device  switches on its power LED, the range extender also does so.
  3. Your smart device’s settings menu will let you choose WiFi.
  4. On the connection, select “Wavlink Aerial Extender Setup Ext”.
    Once you’re connected, launch your mobile device’s web browser.
  5. It is necessary to type the address exactly as it appears in the link bar.
  6. The new configuration page for the range extender will open.
    Refer to the detailed instructions to set up the extender.